Hi,
I try to change the fuses No change
Do I have to feed the HV Rescue Shield 2. with 12V?
Any suggestions?
Thanks.
I can not change the fuses
Re: I can not change the fuses
Hi brunortt,
Sorry for the delay in my reply.
The rescue shield contains its own 12V supply so you do not need to provide one.
Can you tell me more about what chip you are trying to use with the shield? Was the chip working normally before? What version of the Arduino sketch are you using, and what version of Arduino?
Make sure the chip is inserted with pin 1 in the correct location as it seems like the chip is not responding.
Sorry for the delay in my reply.
The rescue shield contains its own 12V supply so you do not need to provide one.
Can you tell me more about what chip you are trying to use with the shield? Was the chip working normally before? What version of the Arduino sketch are you using, and what version of Arduino?
Make sure the chip is inserted with pin 1 in the correct location as it seems like the chip is not responding.
Jeff Keyzer
http://mightyohm.com
http://mightyohm.com
Re: I can not change the fuses
Hi mightyohm,
Thanks for answering
Thanks
Thanks for answering
The chip on the ATMEGA328PCan you tell me more about what chip you are trying to use with the shield?
The chip worked fine, and when I try to load a program no longer respondsWas the chip working normally before?
Arduino version is 1.6.5 and I tried both version of the sketch Arduino Uno as Arduino Mega, with the same result as seen in the image aboveWhat version of the Arduino sketch are you using, and what version of Arduino?
Make sure the chip is inserted with pin 1 in the correct location as it seems like the chip is not responding
Thanks
Re: I can not change the fuses
I see that you are using an Arduino MEGA. Did you set #define MEGA 1 in the Arduino sketch?
http://mightyohm.com/blog/2011/03/hv-re ... uino-mega/
http://mightyohm.com/blog/2011/03/hv-re ... uino-mega/
Jeff Keyzer
http://mightyohm.com
http://mightyohm.com
Re: I can not change the fuses
Hi mightyohm,
Set the MEGA #define to 1 and compile/upload the sketch to your board
But as usual
Thanks
Set the MEGA #define to 1 and compile/upload the sketch to your board
But as usual
Thanks
Re: I can not change the fuses
After changing MEGA to 1, did you remove the ATMEGA328 from the rescue shield before clicking the "Upload" button in the Arduino IDE?
It seems like maybe the change in code did not get compiled and uploaded to the board. The behavior you are seeing (fuses = 3) can happen if the code running on the Arduino is not compiled for the Mega.
Other things to try -Check all of your solder joints. Try the shield with an Arduino Uno if you have one around - most of my testing has been done with the Uno. Make sure the ATMEGA328 is not plugged into the socket when you upload the sketch or open the serial monitor. Try a spare ATMEGA328 if you have one to make sure the chip isn't bad.
I just verified that the shield works with the latest Arduino IDE (1.6.5) and both the Uno and a Mega 2560. Everything seems to be working fine here.
It seems like maybe the change in code did not get compiled and uploaded to the board. The behavior you are seeing (fuses = 3) can happen if the code running on the Arduino is not compiled for the Mega.
Other things to try -Check all of your solder joints. Try the shield with an Arduino Uno if you have one around - most of my testing has been done with the Uno. Make sure the ATMEGA328 is not plugged into the socket when you upload the sketch or open the serial monitor. Try a spare ATMEGA328 if you have one to make sure the chip isn't bad.
I just verified that the shield works with the latest Arduino IDE (1.6.5) and both the Uno and a Mega 2560. Everything seems to be working fine here.
Jeff Keyzer
http://mightyohm.com
http://mightyohm.com
Re: I can not change the fuses
Hi mightyohm,
I tried it with a new chip (ATMEGA328P), and I changed the fuses seamlessly
So the compilation and communication with arduino is correct for the mega
But that I can do with a programmer (USBtiny)
I think the HV Shield Rescue 2 is not working on high voltage (HVPP)
Thanks
I tried it with a new chip (ATMEGA328P), and I changed the fuses seamlessly
So the compilation and communication with arduino is correct for the mega
But that I can do with a programmer (USBtiny)
I think the HV Shield Rescue 2 is not working on high voltage (HVPP)
Thanks
Re: I can not change the fuses
The rescue shield uses a completely different protocol from avrdude so if it works on one part, the 12V HVPP must be working. Most likely the first chip you tried is damaged somehow.
Jeff Keyzer
http://mightyohm.com
http://mightyohm.com